1. Welcome to Tacoma World!

    You are currently viewing as a guest! To get full-access, you need to register for a FREE account.

    As a registered member, you’ll be able to:
    • Participate in all Tacoma discussion topics
    • Communicate privately with other Tacoma owners from around the world
    • Post your own photos in our Members Gallery
    • Access all special features of the site

Reliable Low Voltage Disconnect

Discussion in 'Technical Chat' started by wessyder, Jan 20, 2019.

  1. Jan 20, 2019 at 3:45 PM
    #1
    wessyder

    wessyder [OP] Enlightened OR Bro who don't need no skewp

    Joined:
    Jan 3, 2019
    Member:
    #278012
    Messages:
    682
    Gender:
    Male
    Vehicle:
    2019 Tacoma TRD OR, basically an off road race truck
    Tied several boat anchors to my truck to destroy MPG.
    Anyone have a reliable low voltage disconnect make/model they can recommend?
    Looking to kill a lighting circuit if left on too long (accidental or otherwise) before it kills the battery. Bonus points if it has a manual override switch. Looking for something that won't die if it gets damp or is jarred a bit.
     
  2. Jan 21, 2019 at 1:13 AM
    #2
    Wyoming09

    Wyoming09 Well-Known Member

    Joined:
    Apr 24, 2015
    Member:
    #153833
    Messages:
    14,277
    Gender:
    Male
    New Tripoli Pa
    Vehicle:
    2000 Work truck 5 speed 4x4 3.4
    Super Springs
    How do you want to have the switch work when battery voltage drops below a certain voltage.

    By a timer after so many minutes

    having a manual over ride kinda defeats the whole idea
     
  3. Jan 21, 2019 at 6:20 AM
    #3
    96carboard

    96carboard Well-Known Member

    Joined:
    Sep 14, 2018
    Member:
    #266237
    Messages:
    1,593
    There are about 10 trillion different ways to do this.
    And what I recommend would probably change depending on a number of different elements, such as how much current the circuit will carry, whether you want to control just one or multiple circuits with the same controller, DC or AC (most low voltage stuff is DC, but some is AC, like a furnace thermostat or doorbell), whether your accessory is looped back, or terminates at some other location, etc.

    One of my favorite ways of switching circuits is with a microcontroller and FET -- which will easily let you control it with timers, as well as any kind of override you like, but FETs only works with DC, and depending on whether the accessory loops back or terminates remotely impacts the choice between N-channel and P-channel FET. N-channel can typically carry much more current (~10x), but is to be implemented as a LOW SIDE switch, so this would be for loopback configuration. You can do a remote termination with a P-channel FET, but like I mentioned, much lower current. AC power is best done with a relay.
     
  4. Jan 21, 2019 at 6:23 AM
    #4
    golfindia

    golfindia Well-Known Member

    Joined:
    Aug 25, 2017
    Member:
    #228000
    Messages:
    2,864
    Yes.
    Vehicle:
    pickup truck
  5. Jan 21, 2019 at 8:19 AM
    #5
    wessyder

    wessyder [OP] Enlightened OR Bro who don't need no skewp

    Joined:
    Jan 3, 2019
    Member:
    #278012
    Messages:
    682
    Gender:
    Male
    Vehicle:
    2019 Tacoma TRD OR, basically an off road race truck
    Tied several boat anchors to my truck to destroy MPG.
  6. Jan 21, 2019 at 8:33 AM
    #6
    wessyder

    wessyder [OP] Enlightened OR Bro who don't need no skewp

    Joined:
    Jan 3, 2019
    Member:
    #278012
    Messages:
    682
    Gender:
    Male
    Vehicle:
    2019 Tacoma TRD OR, basically an off road race truck
    Tied several boat anchors to my truck to destroy MPG.
    Yeah I was just looking to prevent draining the battery totally or to levels that would damage it. Override would just be an emergency thing that would just make it so I could use that circuit regardless in an emergency situation (battery be damned).
     

Products Discussed in

To Top